Welcome Guest!!!

Thank you for visiting the GM Kappa Performance Forum. This forum is the only performance oriented forum for all GM Kappa Platform Enthusiasts.  We hope you will join and share your experiences.  Becoming a member is FREE! If you want to advertise on this forum, email KappaPerformance at yahoo.com.

Registration required to view the forum attachments. Below is a sample of the current top 25 topics.
Supporting Membership has many advantages.

More information on becoming a supporting member or vendor can be found on the sub forum; Site Help and Suggestions; thread - Supporting Members and Vendors.
Pages: [1]   Go Down

Author Topic: What would cause these codes p0650 and p1288  (Read 1299 times)

0 Members and 1 Guest are viewing this topic.

Offline IBDRINKEN

  • Premium Member
  • Gearhead
  • *
  • Posts: 1689
  • Karma: +3/-0
  • Location: JACKSONVILLE FL
  • Donkey Master
What would cause these codes p0650 and p1288
« on: April 21, 2014, 06:10:51 PM »
So we installed the solo cat and race exhaust a couple of weekends ago and recently on first start up it will sputter real bad and shoot black smoke out of the exhaust then it throws these codes p0650 and p1288. Any idea what would cause this and also could it be that the tune needs adjusting.
Logged
13.5@101.90
320HP 358 Torque
Solo Hi Flow Cat/ 3in dual exhaust
Kappa Intake
Dakota Digital EG, Boost Gauage, Oil Temp, Oil Pressure, Fuel Pressure
DDM Probeam, Backbone, IC Pipes, Coilcover Cross Brace
JPM Shifter, Center Console
DDM Intercooler
AEM Water/Meth Injection

Offline Critterman

  • Retired, thank you very much
  • Premium Member
  • General Manager
  • *
  • Posts: 13583
  • Karma: +17/-58
  • Baltimore/Washington Corridor
Re: What would cause these codes p0650 and p1288
« Reply #1 on: April 21, 2014, 08:34:39 PM »
P0650-malfunctioning MIL circuit.  (engine indicator light)
P1288-Cylinder head temp sensor.


Check your connections
Logged
GONE: (but not forgotten) 2006 Cool named BIXABEL (BISH-AH-BEL) Mayan for "Good Roads"

DDM
StageIII intercooled Supercharger, Wisco ceramic coated pistons, Carrillo rods, superTech valves and Springs
Ported and polished head
Exedy Stage II Clutch
big brake kit, slotted/drilled Rotors w/Porterfield pads & blue juice
Backbone, Probeam, Cross Strut Brace
Underhood, trunk, & door Lights
ZOK suspension

JPM
Center console, door inserts, & dash
Seat bolster & lumbar support

Focuztech Tri-Y Header & hi-flow cat
Solo Performance SQR-2
Norm's Rear facia
Heated Seats
Black Cat inserts

Offline Wartie

  • Premium Member
  • Master Tech
  • *
  • Posts: 611
  • Karma: +7/-7
  • Location: Stow Ohio
Re: What would cause these codes p0650 and p1288
« Reply #2 on: April 21, 2014, 10:09:07 PM »
Just for the sake of conversation. Does the placement of your Dakota boost and Egt gauge have anything to do with it? Just curious.
http://i86.photobucket.com/albums/k81/ibdrinken/GXP/b9989e2634bc1cc9b21b1b4b51e49764.jpg

Logged

Offline IBDRINKEN

  • Premium Member
  • Gearhead
  • *
  • Posts: 1689
  • Karma: +3/-0
  • Location: JACKSONVILLE FL
  • Donkey Master
Re: What would cause these codes p0650 and p1288
« Reply #3 on: April 21, 2014, 10:53:21 PM »
Quote from: Wartie on April 21, 2014, 10:09:07 PM
Just for the sake of conversation. Does the placement of your Dakota boost and Egt gauge have anything to do with it? Just curious.
http://i86.photobucket.com/albums/k81/ibdrinken/GXP/b9989e2634bc1cc9b21b1b4b51e49764.jpg



At first I thought that but on my old GXP see pic below we put it in the same exact spot

Logged
13.5@101.90
320HP 358 Torque
Solo Hi Flow Cat/ 3in dual exhaust
Kappa Intake
Dakota Digital EG, Boost Gauage, Oil Temp, Oil Pressure, Fuel Pressure
DDM Probeam, Backbone, IC Pipes, Coilcover Cross Brace
JPM Shifter, Center Console
DDM Intercooler
AEM Water/Meth Injection
Pages: [1]   Go Up
 
Powered by EzPortal