Welcome Guest!!!

Thank you for visiting the GM Kappa Performance Forum. This forum is the only performance oriented forum for all GM Kappa Platform Enthusiasts.  We hope you will join and share your experiences.  Becoming a member is FREE! If you want to advertise on this forum, email KappaPerformance at yahoo.com.


Registration required to view the forum attachments. Below is a sample of the current top 25 topics.
Supporting Membership has many advantages.


More information on becoming a supporting member or vendor can be found on the sub forum; Site Help and Suggestions; thread - Supporting Members and Vendors.

Author Topic: Corvette Brembo brake upgrade  (Read 7276 times)

0 Members and 1 Guest are viewing this topic.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Corvette Brembo brake upgrade
« on: March 06, 2019, 09:10:13 PM »
I have successfully fit 4 piston brembo brakes on my 2007 gxp. I have test driven the car and the mechanical side seems to be working properly. I need help with the electrical side. The corvette hub has a different connector than the factory solstice hub. I believe I have all the parts to fashion an adapter pig tail, but I am not sure how to wire them. Any help would be greatly appreciated. I have tons of pictures, but how the heck do you post them on here?

-Machined stock spindles to fit corvette hubs
-Machined bracket to hold calipers
-Extended factory brake hard lines to reach new caliper location
-Temporarily using wheel spacers until wheels are chosen

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #1 on: March 06, 2019, 09:36:17 PM »
The crucial detail here is that both hubs are using the same amount of teeth (same pulses per revolution).  Since they're both made by GM, the tooth count is probably standardized. It should work the first time, if you have a problem than you'll need to swap the two wires.

2006 Solstice Anti-lock brake speed sensor wiring:



How it works:



Okay, now hand it over, the part numbers and pictures that is!!!
2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #2 on: March 06, 2019, 09:49:10 PM »
Thanks for the feed back Steelmesh. I figured that approach would work, I just didn't want it to mess anything up if I wired it backwards. I will try that tomorrow and see what results I can get. Also I can't figure out how to post pictures.[][/]

Offline DeepBlueGXP

  • KappaPerformance Site Owner
  • Administrator
  • Shop Foreman
  • *
  • Posts: 9222
  • Karma: +12/-6
  • Location: Southern Maryland
  • Displaced Buffalo Bills Fan
    • Kappa Performance Forum
Re: Corvette Brembo brake upgrade
« Reply #3 on: March 06, 2019, 10:23:09 PM »
Thanks for the feed back Steelmesh. I figured that approach would work, I just didn't want it to mess anything up if I wired it backwards. I will try that tomorrow and see what results I can get. Also I can't figure out how to post pictures.[][/]
You need a photo hosting site and then you copy the URL and paste it here or like SteelMesh, become a supporting member and you can upload photos directly to the forum.  There is other benefits to becoming a Lifetime Supporting member. 

Joe

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #4 on: March 07, 2019, 07:20:56 AM »
Thanks for the feed back Steelmesh. I figured that approach would work, I just didn't want it to mess anything up if I wired it backwards. I will try that tomorrow and see what results I can get. Also I can't figure out how to post pictures.[][/]

Just use imgur.com no account needed to upload pictures. Other no account free ones are catbox.moe and kek.gg
2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #5 on: March 07, 2019, 11:50:28 AM »
Thanks I will try it out.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #6 on: March 07, 2019, 11:52:58 AM »

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #7 on: March 07, 2019, 01:36:02 PM »
Looks wicked! Does your wheel spacing change?

2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #8 on: March 07, 2019, 02:48:14 PM »
Future state I will not need the wheel spacers, but for now I got a set of take off wheels from a C6. I will be getting custom wheels in the future. I will add some more photos.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #9 on: March 07, 2019, 03:05:05 PM »

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #10 on: March 08, 2019, 12:13:53 PM »
@DeepBlueGXP, what are some of the benefits of becoming a supporting member?

Offline Sol Asylum

  • Premium Member
  • General Manager
  • *
  • Posts: 10354
  • Karma: +40/-66
  • Location: Tolono Illinois
  • THAT'S MISTER KAPPA ASSYLUM TO YOU!
Re: Corvette Brembo brake upgrade
« Reply #11 on: March 08, 2019, 04:33:23 PM »
Unlocks other sections of the forum like digital copies of the service manuals.  Reduced or eliminates ads to name a few.
2007 Aggressive GXP

Offline Sly Bob

  • Administrators
  • Shop Foreman
  • *
  • Posts: 8033
  • Karma: +19/-10
  • Location: Welland, Ontario, Canada
  • My new grandson
    • Kappa Performance Forum
Re: Corvette Brembo brake upgrade
« Reply #12 on: March 08, 2019, 09:47:42 PM »
@DeepBlueGXP, what are some of the benefits of becoming a supporting member?
This should help.
http://www.kappaperformance.com/forum/index.php/topic,8516.msg132160.html#msg132160
Just trying to do my part...

Mods: Lose the chicklets, VentureShield, Dual horns, AfterShock spoiler, Weathershield cover, Lil Chromies, Red calipers with black Solstice stickers, Opel GT antenna and Solo GXP-RCD exhaust with a Solo hi-flow cat!

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #13 on: March 09, 2019, 09:23:30 PM »
@DeepBlueGXP, what are some of the benefits of becoming a supporting member?

This forum is not sold out to a gigantic money gobbling corporation like the majority of automotive forums including the other kappa forums.  :thumbs:

They bought out all these forums, then integrated their own forum software package to blast people with advertisements and track them.  A few years ago, this was brought to light when they got hacked and most people didn't know why they needed to change their passwords on several totally different car platform forums.  It was because they are all connected to a single system that got compromised. 

2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline bogie

  • Apprentice/Gofer
  • *
  • Posts: 3
  • Karma: +0/-0
  • Location: utah
Re: Corvette Brembo brake upgrade
« Reply #14 on: March 10, 2019, 10:39:45 PM »
I am new here, and new to Solstice. I've had my car for two weeks now and will put several thousand miles on it before I make any decisions on what I may or may not want to change, so I'm just sort of watching to see what Solstice owners are doing. Big brakes are always good, but it looks like the shocks and springs are stock, and it seems that one of the first things done to these cars are shocks and springs. And just for curiosity, what is the copper line in the background?

Offline Critterman

  • Retired, thank you very much
  • Premium Member
  • General Manager
  • *
  • Posts: 13602
  • Karma: +17/-58
  • Baltimore/Washington Corridor
Re: Corvette Brembo brake upgrade
« Reply #15 on: March 11, 2019, 10:15:48 AM »
That is a brake line you can follow it all the way to the caliper
GONE: (but not forgotten) 2006 Cool named BIXABEL (BISH-AH-BEL) Mayan for "Good Roads"

DDM
StageIII intercooled Supercharger, Wisco ceramic coated pistons, Carrillo rods, superTech valves and Springs
Ported and polished head
Exedy Stage II Clutch
big brake kit, slotted/drilled Rotors w/Porterfield pads & blue juice
Backbone, Probeam, Cross Strut Brace
Underhood, trunk, & door Lights
ZOK suspension

JPM
Center console, door inserts, & dash
Seat bolster & lumbar support

Focuztech Tri-Y Header & hi-flow cat
Solo Performance SQR-2
Norm's Rear facia
Heated Seats
Black Cat inserts

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #16 on: March 11, 2019, 10:19:40 AM »
I am new here, and new to Solstice. I've had my car for two weeks now and will put several thousand miles on it before I make any decisions on what I may or may not want to change, so I'm just sort of watching to see what Solstice owners are doing. Big brakes are always good, but it looks like the shocks and springs are stock, and it seems that one of the first things done to these cars are shocks and springs. And just for curiosity, what is the copper line in the background?

Looks like copper tubing, maybe it's copper clad metal line.  Using copper tube is dangerous, look at the working pressure: https://www.engineeringtoolbox.com/copper-tubes-dimensions-pressure-d_84.html

Copper starts to anneal around 800F, that is pretty extreme but it's possible for the rotors to exceed this temp hardcore racing.

In addition, compression fittings specifically say on the box not to use with braking systems.

These days, most auto parts store offer easy to bend brake lines, combine that with a flare tool + bender + cutter then you can custom build any brake line.

« Last Edit: March 11, 2019, 10:23:31 AM by Steelmesh »
2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline bogie

  • Apprentice/Gofer
  • *
  • Posts: 3
  • Karma: +0/-0
  • Location: utah
Re: Corvette Brembo brake upgrade
« Reply #17 on: March 11, 2019, 10:56:36 AM »
If it is really is the brake line, change it to steel for safety sake. It's cheap, premade, and available in any parts store. A 20 or 30 inch one should cost about five dollars or so and will have two nuts and a double flair on both ends.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #18 on: March 12, 2019, 10:42:12 PM »
Sorry for the delay, work has been crazy thus past week!

Thanks for the information on becoming a member, I think I will join in the near future

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #19 on: March 12, 2019, 10:52:30 PM »
The copper line referred to in the photo is in fact a break line. It is a Copper Nickel alloy that is rated and designed for break lines. I did a fair amount of research before selecting this material. I purchased the tube from a local automotive parts store and it cam with one end already flared and the other end straight cut. After bending the tube and cutting to length, I then flared the other end. I will see if I can find the test results I found comparing steel and the copper nickel alloy.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #20 on: March 12, 2019, 10:57:22 PM »
So far I have one week of driving on the breaks and other than the dang lights on the dash, they are working great. I have tried swapping the connections around on the wheel speed sensor to no avail!

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #21 on: March 13, 2019, 09:52:43 AM »
The copper line referred to in the photo is in fact a break line. It is a Copper Nickel alloy that is rated and designed for break lines. I did a fair amount of research before selecting this material. I purchased the tube from a local automotive parts store and it cam with one end already flared and the other end straight cut. After bending the tube and cutting to length, I then flared the other end. I will see if I can find the test results I found comparing steel and the copper nickel alloy.

Thanks for clarifying, lots of us feeling triggered.

https://www.jegs.com/p/JEGS/JEGS-NiCopp-Nickel-Copper-Brake-Lines/2111534/10002/-1

Does not corrode, easy to bend and flare (HF tool might actually work!), sounds like a dream come true
2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline Steelmesh

  • Premium Member
  • Master Tech
  • *
  • Posts: 682
  • Karma: +5/-2
  • Location: Detroit Metro
    • Kappadapt
Re: Corvette Brembo brake upgrade
« Reply #22 on: March 13, 2019, 10:06:32 AM »
So far I have one week of driving on the breaks and other than the dang lights on the dash, they are working great. I have tried swapping the connections around on the wheel speed sensor to no avail!

Can you see the reluctor ring teeth?  Maybe pull the sensor and look inside, need to have the same teeth count.  This may be the problem.  If you have an oscilloscope you should be able to count it that way test the solstice and corvette to compare.  In addition, you can compare the signal strength, magnitude of the sinusoid.

Example signal:


At work we have expensive equipment to emulate speed sensor outputs to feed the ECU, where the dyna sends the speed to the emulator then the emulator sends the signal to the ECU.  I have never programmed this equipment so I don't have deep knowledge of the nuances here to get it to work...this is just proof you can spoof the signal without using the exact setup the car came with.



2006 Solstice #1458, Twincharged LE5/LEA, 5757+M62, Werks exh manifold, Tial bpv/wg, Cams, dual meth, 40 PSI lol without ring seal, Kappadapt clutch hose/flywheel bolts/trans mount, Aisin AR5, Stage 5 clutch
Turbo-only power 444whp/422wtrq

2013 Cruze Missile, tuned, 42 lb, ZZP SRI/FMIC/DP/MP/CB, Kappadapt trans mount

Support Kappaperformance.com!!  Note: a couple huge corporations own and control several hundred of the top automotive enthusiast forums subsequently profiteering from these communities on the backs of volunteer moderators.

Offline bogie

  • Apprentice/Gofer
  • *
  • Posts: 3
  • Karma: +0/-0
  • Location: utah
Re: Corvette Brembo brake upgrade
« Reply #23 on: March 13, 2019, 12:24:54 PM »
I looked up copper brake lines also, and learned something new today. Glad for that. I just retired from 40 or so years in the auto parts business and had never heard of copper brake lines. Thanks for the incite.

Offline silverghost

  • Apprentice/Gofer
  • *
  • Posts: 13
  • Karma: +0/-0
  • Location: birmingham, al
Re: Corvette Brembo brake upgrade
« Reply #24 on: March 17, 2019, 08:11:37 PM »
@steel mesh, those are like the lines I got. Only difference is I swapped out the black painted fittings for yellow zinc coated fittings to further protect it from corrosion.

 

Powered by EzPortal