Welcome Guest!!!

Thank you for visiting the GM Kappa Performance Forum. This forum is the only performance oriented forum for all GM Kappa Platform Enthusiasts.  We hope you will join and share your experiences.  Becoming a member is FREE! If you want to advertise on this forum, email KappaPerformance at yahoo.com.


Registration required to view the forum attachments. Below is a sample of the current top 25 topics.
Supporting Membership has many advantages.


More information on becoming a supporting member or vendor can be found on the sub forum; Site Help and Suggestions; thread - Supporting Members and Vendors.

Author Topic: NEED: (Pics added) How to change the stock clamps to T-Bolt clamps please?  (Read 12270 times)

0 Members and 1 Guest are viewing this topic.

Offline KWhale

  • Playing with my
  • Premium Member
  • Master Tech
  • *
  • Posts: 870
  • Karma: +0/-0
  • Location: Gibbons, Alberta, Canada eh
Deep - I did remove the rubber pieces from the tube where Clamp 5 and 6 go.  My problem was a fear of crushing something so I did not tighten them down tight enough.  I put clamp 5 back in place and tightened it as much as I dared (much harder than the first time) then went around and tightened 4,4a and 6 as well.  Seems to be holding after a couple of short but hard drives.
The most Northern Senior Member on the map!!!
http://kappaperformance.com/forum/index.php?action=googlemap

Offline DeepBlueGXP

  • KappaPerformance Site Owner
  • Administrator
  • Shop Foreman
  • *
  • Posts: 9220
  • Karma: +12/-6
  • Location: Southern Maryland
  • Displaced Buffalo Bills Fan
    • Kappa Performance Forum
Good, you were supposed to, good job!

Offline Critterman

  • Retired, thank you very much
  • Premium Member
  • General Manager
  • *
  • Posts: 13600
  • Karma: +17/-58
  • Baltimore/Washington Corridor
I know its not much but since the mod meet I have spent over a grand with Dave :/

Don't stop now, keep on spending, I'm sure they appreciate it.  :)
GONE: (but not forgotten) 2006 Cool named BIXABEL (BISH-AH-BEL) Mayan for "Good Roads"

DDM
StageIII intercooled Supercharger, Wisco ceramic coated pistons, Carrillo rods, superTech valves and Springs
Ported and polished head
Exedy Stage II Clutch
big brake kit, slotted/drilled Rotors w/Porterfield pads & blue juice
Backbone, Probeam, Cross Strut Brace
Underhood, trunk, & door Lights
ZOK suspension

JPM
Center console, door inserts, & dash
Seat bolster & lumbar support

Focuztech Tri-Y Header & hi-flow cat
Solo Performance SQR-2
Norm's Rear facia
Heated Seats
Black Cat inserts

Offline Gentleman Jack

  • Chief Financial Officer, Color Professional
  • Premium Member
  • Shop Foreman
  • *
  • Posts: 8991
  • Karma: +25/-82
  • Location: Unknown
  • I'm here. If I wasn't here, I'd be there.
I know its not much but since the mod meet I have spent over a grand with Dave :/

Good!  Could you order me up some stuff?

GJ
Make the right choices now

Offline IBDRINKEN

  • Premium Member
  • Gearhead
  • *
  • Posts: 1689
  • Karma: +3/-0
  • Location: JACKSONVILLE FL
  • Donkey Master
maybe soem clamps :)
13.5@101.90
320HP 358 Torque
Solo Hi Flow Cat/ 3in dual exhaust
Kappa Intake
Dakota Digital EG, Boost Gauage, Oil Temp, Oil Pressure, Fuel Pressure
DDM Probeam, Backbone, IC Pipes, Coilcover Cross Brace
JPM Shifter, Center Console
DDM Intercooler
AEM Water/Meth Injection

 

Powered by EzPortal