Author Topic: What did you do to your Kappa today! (Read 1264739 times)

SHiNY · « **Reply #3775 on:** May 14, 2011, 06:10:05 PM »

Had my brother fix my tire. I have the Hankook Ventus V12 so they are directional. Three were doing one way, one was going the other. Dumbasses! Now they are all going in one direction

P.S. I have the Gravagna J2 rims. According to my brother they are "a pain in the balls" to switch tires. It appears the large lip causes problems. He flipped the rim and had to remove it and replace it from the back side.

Gentleman Jack · « **Reply #3776 on:** May 15, 2011, 12:18:58 AM »

Your rims give blue balls?

SHiNY · « **Reply #3777 on:** May 15, 2011, 01:32:35 AM »

Quote from: Gentleman Jack on May 15, 2011, 12:18:58 AM

Your rims give blue balls?

Umm... yes?

baconbits · « **Reply #3778 on:** May 15, 2011, 11:52:37 AM »

First ride of the year.. It took 3 days to charge the battery as someone popped the trunk and the light was on ..going for a ride to check my Tacoma at the paintless dent removal shop...154 hail dents in less than 2 minutes last month...3400$ to fix...my only insurance claim in 25 years...I am betting that they will recoup that someway..

G8TR · « **Reply #3779 on:** May 15, 2011, 02:16:54 PM »

Haven't done it yet, however, this evening I will take the cover off, it rained last night, and get it clean. Then about 3am we will leave for the east coast to take another shot at seeing the shuttle launch. Should be perfect weather, about 70 and a clear night with almost a full moon for the ride. The front that just came through should keep it from becoming abrasively hot as the sun rises and for the drive back. Should be a good morning for the launch at about 8:36am.

smartin · « **Reply #3780 on:** May 15, 2011, 02:29:28 PM »

Enjoy! Sounds like fun. My niece is usually there.

kennysabarese · « **Reply #3781 on:** May 15, 2011, 03:07:04 PM »

I just got my stock IC out of the car (without removing the bumper)

Moving the hoses over and found out my DDM T bolt clamps are too big. Putting the stock ones back

Sly Bob · « **Reply #3782 on:** May 15, 2011, 03:14:37 PM »

The DDM clamps I believe would work best with their tubes and IC. I had clamps from Verocious that I bought the last time I was in Wilmington for Mecca. They fit the stock tubes great but when I installed my new DDM tubes a few weeks ago I found that they were too small. I got them on there but it was a tight fit.

DDM clamps likely work best with their tubes. Do you have the DDM tubes Kenny?

1LILNDN · « **Reply #3783 on:** May 15, 2011, 03:19:25 PM »

Quote from: G8TR on May 15, 2011, 02:16:54 PM

Haven't done it yet, however, this evening I will take the cover off, it rained last night, and get it clean. Then about 3am we will leave for the east coast to take another shot at seeing the shuttle launch. Should be perfect weather, about 70 and a clear night with almost a full moon for the ride. The front that just came through should keep it from becoming abrasively hot as the sun rises and for the drive back. Should be a good morning for the launch at about 8:36am.

I was at the last one and watched it from Hotel in Cocoa beach was neat

Arabas · « **Reply #3784 on:** May 15, 2011, 03:31:18 PM »

Quote from: G8TR on May 15, 2011, 02:16:54 PM

Haven't done it yet, however, this evening I will take the cover off, it rained last night, and get it clean. Then about 3am we will leave for the east coast to take another shot at seeing the shuttle launch. Should be perfect weather, about 70 and a clear night with almost a full moon for the ride. The front that just came through should keep it from becoming abrasively hot as the sun rises and for the drive back. Should be a good morning for the launch at about 8:36am.

sounds great!! i wish i could watch a launch too... if i remember it, i will watch it from Nasa TV! Have fun G8TR.

Kenny, how did u manage to get the IC off without removing the bumper??

LatinVenom · « **Reply #3785 on:** May 15, 2011, 04:22:17 PM »

I will probably make a new thread for this but I finally had the Engine light code read today.
This start it two weeks ago.
At 1st I thought it was the MAF, but upon inspection it was clean. There was a little bit of oil film on the bottom of the tube where the MAF is, but since I have not looked at it for well over 3 years, I figure with the K&N filter is probably normal.
Clean it all up but it did not help.
The code is P0243 Turbo solenoid.
However I put some gas in the car today after Auto-zone read the code and so far it has not happened again.
Not sure what could be happening here.

kennysabarese · « **Reply #3786 on:** May 15, 2011, 04:23:51 PM »

I have stock tubes and RPI IC

I must have gotten the kit that is for their tubes and IC. it's ok the stock ones worked out fine.

Arabas: I took the bottom plastics out and pulled it down. It was hard but it came out. then i put some plastic back and pushed the new one up, now putting the rest of the plastic back.

BigSal · « **Reply #3787 on:** May 15, 2011, 04:26:03 PM »

I replaced the plugs and cleaned the MAF sensor and cleaned and re-oiled the CAI filter. Getting ready for the Mod Meet!

BigSal & Bryan

Aspenrose · « **Reply #3788 on:** May 15, 2011, 04:37:31 PM »

Just put 3 quarts of Mobil 1 in it:-(

HAMMER DOWN · « **Reply #3789 on:** May 15, 2011, 04:48:28 PM »

^^^ That's not good, no oil light & how many miles sense the last oil change.

Mike

smartin · « **Reply #3790 on:** May 15, 2011, 04:48:56 PM »

Same thing I've been doing for the last week or more -- detailing and driving and detailing and driving. It's been gorgeous!

spicy3480 · « **Reply #3791 on:** May 15, 2011, 04:54:45 PM »

Upgrading to bigger 8" speakers in the doors and ring radiator tweeters using pods. It will be a nice project for the weekend.

SHiNY · « **Reply #3792 on:** May 15, 2011, 05:02:59 PM »

Quote from: Aspenrose on May 15, 2011, 04:37:31 PM

Just put 3 quarts of Mobil 1 in it:-(

That's not good

smartin · « **Reply #3793 on:** May 15, 2011, 05:09:03 PM »

Quote from: spicy3480 on May 15, 2011, 04:54:45 PM

Upgrading to bigger 8" speakers in the doors and ring radiator tweeters using pods. It will be a nice project for the weekend.

I bet that's going to sound awesome! Make sure to let me hear them at the mod meet.

TomatoSoup · « **Reply #3794 on:** May 15, 2011, 05:18:33 PM »

Working on a custom mount for my Ultragauge today. It will attach to the ~~left~~ right of the steering column placing the UG above the right switch stalk.

I probably won't take pics, 'cos nobody cares about my mods. (Sob!)

(Corrected)

Sly Bob · « **Reply #3795 on:** May 15, 2011, 05:42:14 PM »

Quote from: TomatoSoup on May 15, 2011, 05:18:33 PM

Working on a custom mount for my Ultragauge today. It will attach to the left of the steering column placing the UG above the right switch stalk.

I probably won't take pics, 'cos nobody cares about my mods. (Sob!)

Snap out of it!

Get that camera charged 'cause we expect some pics, not here but in ti's own thread!

Kelu · « **Reply #3796 on:** May 15, 2011, 06:03:52 PM »

TO: really want to see that, thinking to buy a UG also. Please?

Critterman · « **Reply #3797 on:** May 15, 2011, 06:08:05 PM »

Buy it now, 69 dollars have it delivered to Joe's and take it home with you. I have one in the truck, and will get one for the wife's car.

Kelu · « **Reply #3798 on:** May 15, 2011, 06:13:11 PM »

Critter: i know is great price but I want also some other things too like brake pads

and not sure what other "surprises" I will get from turbo upgrade

1LILNDN · « **Reply #3799 on:** May 15, 2011, 07:59:20 PM »

Quote from: TomatoSoup on May 15, 2011, 05:18:33 PM

Working on a custom mount for my Ultragauge today. It will attach to the left of the steering column placing the UG above the right switch stalk.

I probably won't take pics, 'cos nobody cares about my mods. (Sob!)

Mark thats bull Chit I always read your post and the Mods you do and hope I can do it. C U @ the Mods Meet

News:

Author Topic: What did you do to your Kappa today! (Read 1264739 times)